How to Get Window Mode Shortcut Again Maplelegend

Offline
Polarstars Blueish Snail

May 12, 2020

Female

6:26 PM

8/ten too much water

Beginner

(Im on windows10)
Maple wont launch at all, information technology but gives me the fault. But the setup.exe works only fine (I can meet the billowy paradigm, press alt + h, and get the message nigh it setting the scanning frequency to 75hz).
CRU app looks like this

Plainly im doing something wrong. Is there whatever other information i would need to give that would help?
Offline
DrJason Capt. Latanica

May thirty, 2018

Male

Canada

eight:26 PM

DrJason, Zrar

Islander, F/P Arch Mage

Kouhai

I take to give the annoying suggestion first: brand sure your graphic carte du jour driver is up to appointment
Your default resolution of 1680x1050 might be why. Endeavor to add a different resolution that fits one of maplelegends supported resolutions at the acme (where it says 3 slots left).
Are you using a AMD graphic card? If so open Radeon Software (right click on desktop, it should exist a pinned shortcut) ensure that GPU scaling and virtual super resolution are both enabled under "Display". If you are using an Nvidea or other graphic card I am unfamiliar but there are likely similar settings to cheque.

These are things I take had to bank check whenever I encounter Gr2d errors, so just using my personal experience here
Offline
Polarstars Blueish Snail

May 12, 2020

Female

6:26 PM

8/10 too much water

Beginner

Good advice, and thanks for replying. I had actually forgotten to update my drivers, so when you suggested it I thought that might be the cause, simply no. Afterwards an update and a reboot it even so didn't launch.
I input 800x600 @ 60hz in the field you specified and withal got the same error after a reboot.
Im using an Nvidea carte du jour and none of the options yous described to exist on your AMD seem to be in my command console.
Offline
kalash Headless Horseman

October 18, 2016

Male

two:26 AM

Kalash

Night Lord

198

Halcyon

Do other HD settings work for yous? The ones from legends.ini?
When I connect my screen via usb3, only 0 and 1 piece of work for me. 2 gives gr2d. When I connect it via vga or hdmi theres no trouble. Maybe yous've got the same problem
Offline
Polarstars Blue Snail

May 12, 2020

Female

six:26 PM

8/10 too much water

Beginner

A good thought. You'd think if it's a resolution thing that that'd work or at to the lowest degree assistance, but after playing with the resolution options in the legends.ini config, neither 0, 1, or 2 piece of work. I still get the same gr2D error no matter what.
Offline
DrJason Capt. Latanica

May 30, 2018

Male person

Canada

viii:26 PM

DrJason, Zrar

Islander, F/P Arch Mage

Kouhai

I found this commodity that explains GPU scaling and how to enable it for a Nvidea card: https://gamegavel.com/what-is-gpu-scaling/
Not having it enabled would requite Gr2d errors as the commodity explains, but at that place could exist a separate issue as well. If y'all accept whatever other monitor/TV endeavour using that, it would help narrow down the trouble from existence your display or your graphic card.
Offline
Polarstars Bluish Snail

May 12, 2020

Female

6:26 PM

8/10 too much water

Beginner

I followed the guide and changed the scaling to gpu in the nvidea command panel, but it withal gave me the gr2D error.
Also, i but have the one monitor and have no backup/extras so I can't try the second affair you suggested.
Offline
Teddy Blue Snail

May fourteen, 2020

Male

eight:26 PM

This worked for me (I likewise have NVidea with Windows 10). I went to display settings on my reckoner and inverse the resolution to the resolution i want to play on ( 1366 ten 768). and one time i did that opened the app and it worked. I even changed it dorsum to the normal resolution later on opening the application and information technology was still open(Just dont get to settings in the game or you'll dc). Hope this helps!