How to Make Popsockets Sticky Again

Download Article

Download Article

PopSockets are very useful for getting a better grip on your phone, but they tin get muddy with fourth dimension and the adhesive that sticks it to the back of your phone can become loose and lose its stickiness. After removing it from your phone, just soak it in water and scrub it with soapy water your PopSocket to brand it look good every bit new and stick equally if y'all bought it yesterday.

1. 1

   Fill up a shallow dish with cold tap water. Grab a shallow dish, such as a small bowl or a deep plate, and fill it with most .v in (1.3 cm) of very cold tap water. This is to ensure that you only soak the adhesive side of the PopSocket — you should clean the plastic grip separately.

   • Even if your PopSocket is larger than normal, using only a .v in (ane.3 cm) layer of water volition ensure that only the adhesive side touches the h2o when it is extended.

2. ii

   Remove the popsPopSocketocket and place information technology viscid-side down in the h2o. Dig your fingernail under the PopSocket to pry it off of your phone, then pull the plastic grip to information technology extend to its full length. Place the adhesive side downwards in the water so the plastic grip pokes above the surface of the h2o.

   • Be sure that your extended PopSocket rises above the surface and drain out water as necessary to avoid getting the rest of information technology wet.^[1]

   Advertisement

3. 3

   Permit the PopSocket soak for about 10 seconds, and so remove information technology. Don't disturb the h2o and don't take information technology out earlier 10 seconds are up. One time 10 seconds have passed, quickly accept it out of the h2o by the grip and shake off whatsoever excess water. Do not let it soak for more 10 seconds or it could ruin the adhesive. ^[2]

   • If you lot are concerned about ruining the agglutinative, run the PopSocket nether cold h2o for a few seconds instead, although soaking information technology is more effective.^[3]

4. 4

   Lay a newspaper towel down and identify the PopSocket sticky-side upwardly. You can utilize a regular kitchen towel or a linen towel, depending on what yous have readily available. Lay the PopSocket with the viscous side pointing upwards and the design and plastic grip touch the newspaper.^[4]

5. 5

   Let the agglutinative side of the PopSocket dry for 10 minutes. Get out your PopSocket to dry for x minutes at virtually, and go along an center on it every bit it dries to see if it finishes sooner.^[5] Avoid using a hair dryer or dabbing it with a towel or you could damage the adhesive and brand information technology less sticky. Just allow it air dry, and swiftly re-attach information technology to your phone the moment it is dry out by pressing the viscid side firmly onto the dorsum of your telephone.

   • Do not let your PopSocket dry for more than 15 minutes at virtually or information technology may lose its power to stick.
   • If you accidentally leave information technology out, run it under cold water for a few seconds then allow it dry once more, although be aware that it may not regain its stickiness.

   Advertizement

1. 1

   Remove any additional stickers yous've added to the end of the PopSocket. If you added stickers to the PopSocket's grip, yous volition demand to remove them before you clean information technology. If the adhesive is still expert on the sticker feel free to put it back on later cleaning, otherwise y'all will have to only throw it abroad and find a new i.

   • Popsockets ordinarily come with some kind of design on the stop of the grip, so even if you have to remove any additional stickers you've added, information technology will still have an artful pattern.^[6]

2. 2

   Remove the PopSocket and run the plastic grip under cold water. Use your fingernail to pry the PopSocket off of your phone, then hold the agglutinative side of the PopSocket and turn your water faucet to a low flow on cold. Run only the plastic grip of the PopSocket under water — if you must, wrap the agglutinative in a hand towel to prevent getting it wet and affecting its stickiness.

   • Y'all tin clean the adhesive separately, but if yous go it moisture earlier you're ready to clean information technology, you lot could cause the adhesive to lose some of its stickiness. Wrap information technology or have care to not get it wet while cleaning the grip.

3. three

   Scrub the plastic grip with the corner of a soapy rag, fugitive the adhesive. Hold the PopSocket by the gummy side again and scrub the plastic grip with the corner of a soapy rag PopSocket. Take intendance to avert getting soap on the adhesive, and only scrub the plastic parts of the PopSocket.

   • Scrub inside the grooves of the PopSocket'south expandable eye section with a cotton fiber swab soaked in soapy h2o.
   • Use 70 percent rubbing alcohol to particularly stubborn stains or crud with a cotton wool swab, then rinse it under water over again. Rubbing alcohol is great for removing stains as information technology evaporates quickly and leaves no impairment.

4. 4

   Rinse the grip once again, and so dry it with a paper towel or rag. Run the grip under water to get rid of soapy residue and rubbing alcohol, again taking care to avoid getting the agglutinative wet. Then, accept a dry rag or a paper towel and dab the PopSocket dry until it is completely complimentary of water.^[7] Press information technology firmly onto the dorsum of your phone with the sticky-side down.

   • You can also air dry the plastic grip. Expand the PopSocket and then balance it on its side on a paper towel. This prevents the adhesive from sticking to the towel and will still allow the grip to air dry and drip dry out.

   Advertizing

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertisement

• After re-attaching the PopSocket to your phone, look at least i 60 minutes before you extend the grip and use it. This allows enough time for the adhesive to fully stick to your telephone, reducing the risk of information technology detaching of a sudden.^[viii]

Thank you for submitting a tip for review!

Advertisement

• Avert using rubbing alcohol in a airtight room, and have the PopSocket to a well-ventilated expanse to prevent inhaling rubbing alcohol fumes.

• Never let the sticky side of the PopSocket be exposed to air for more than 15 minutes, even when cleaning the plastic grip, as this destroys the adhesive.

Advertisement

About This Commodity

Thanks to all authors for creating a page that has been read 28,873 times.

Is this article upward to appointment?

looneythroce.blogspot.com

Source: https://www.wikihow.com/Clean-a-PopSocket

Share this post